Flywoo GOKU GN745 45A AIO V3

Since its launch, the GOKU GN745 AIO has stood as Flywoo's top-tier AIO product, earning widespread acclaim from Betaflight, INAV, and Ardupilot enthusiasts. Now, we're excited to introduce the latest upgrade in this series—the V3 version! The V3 boasts a new ESC two-in-one drive solution, enhancing the continuous current capacity to 45A and improving the overcurrent protection capability of the motor pads, resulting in a more powerful overall performance. Furthermore, the V3 version significantly advances in terms of convenience, featuring 4 new direct-plug Uart ports and adopting a Type-C interface for easier connectivity.

Highlights

• Performance: Utilizes STM32F745 chip, AM32 firmware, and MPU6000 gyro, with dual BEC, barometer, black box, supports 7 serial ports and I2C.
• Plug & Play: Compatible with O3 air unit, GPS, Camera, Analog VTX, and Receiver without the need for soldering.
• Type-C Interface: Features a Type-C interface for improved compatibility and easier connection.
• Compatibility: Supports BF, INAV, and Ardupilot platforms.
• New Layout: New ESC two-in-one drive solution, with a continuous current up to 45A.
• Better Protection: Larger motor pad area with improved overcurrent protection.

GOKU GN745 45A AIO 32bit (MPU6000) V3

• Firmware: STM32F745 BGA
• Continuous Current: 45A-50A MAX
• BEC: 5V 2A
• ESC: 32bit
• Flash: 1MB
• Black Box: 16mb
• Barometer: DPS310/SPL06
• Gyro: MPU6000
• Motor: M1-M4 OUTPUT I2C: SCL/SDA
• Uarts: 1,2,3,4,5,6,7
• Plug Uart Ports: YES
• Connector: Type-C
• OSD: AT7456E
• Hole: 25.5*25.5-3mm
• Size: 33.5x33.5mm
• Weight: 9.4g

Specifications

• BF Flight Controller Firmware: FLYWOOF745AIO
• INAV Firmware: FLYWOOF745
• Ardupilot Firmware: FLYWOOF745
• MCU: STM32F745 32-bit processor, 216MHz, 1MB Flash
• IMU: MPU6000 (SPI)
• Barometer: SPL06
• USB VCP Driver: All UARTs usable simultaneously; USB does not take up a UART
• 7 Hardware UARTS: UART1,2,3,4,5,6,7
• Supports Serial Receivers: SBUS, iBus, Spektrum, Crossfire only.
• PPM and PWM Receivers: Not supported.
• Onboard 16Mbytes: For Blackbox logging
• 5V Power Out: 2.0A max
• 3.3V Power Out: 0.5A max
• Dimensions: 33.5x33.5mm
• Mounting Holes: Standard 25.5/26.5mm square to center of holes
• Weight: 9.4g

Onboard 4in1 ESC

• Support: AM32
• Support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
• Input Voltage: 2-6S Lipo
• Continuous Current: 45A
• Firmware: GOKU_F4A32_PRO

In the Box

• 1x UNICON UPL Capacitor 25V 470UF
• 4x M2x6.6 Shock-Absorbing Ball
• 4x M2 Rubber Ring
• 1x XT30 Power Cable
• 1x DJI O3 Connection Cable
• 1x VTX & Camera Connection Cable
• 1x Receiver Connection Cable
• 1x GPS Compass Connection Cable