Lumenier MICRO LUX V3 F4 30A 20x20 4in1 Stack

Artikelnummer: 16940

69,90 €

inkl. 19% USt., zzgl. Versand

knapper Lagerbestand (1 - 3 Werktage)
Soft Mounts: no
Standoffs: yes

The Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack brings incredible power and performance in a micro sized 20x20 package, with plug and play simplicity. No messy harnesses needed to join the 32bit 30A 4in1 ESC and the F4 OSD Flight Controller. Simply press the two units together lining up the micro pin headers. The 4 motor signals and power/ground are passed directly to the FC. All this in a micro size and weiging only 12g for an FC and 4in1 ESC!

Now you can get all the performance from an F4 based flight controller in a micro size! The Micro LUX V3 includes an on-board Betaflight OSD, and a 4s battery power can connect directly to the unit, it has 16MB on-board flash memory for blackbox recording and more.. Using an On Screen Display has never been simpler, just drag and drop in the Betaflight Configurator.

The powerful 30A 32 bit BLHeli_32 ESC packs all the features of a full size 4in1 ESC into a micro 20x20 sized board. It is compatible with direct power from 4s batteries, making it compatible with most racing drones right out of the box. Now you can build a 5" racing quad with a micro power stack to save weight and size!

The MICRO LUX V3 comes with BetaFlight pre-installed. The MICRO LUX supports both SBUS and PPM inputs as well as DSM/DSMX receivers with both 5v and 3.3v support.

Lumenier Micro LUX V3 F4 Flight Controller

2-4S Direct Lipo input support (5-16v)
On-board BetaFlight OSD
On-board 5v/2A and 3.3v/0.2A regulators
SBUS and PPM support
RGB LED dedicated pad and Buzzer Pad
VBAT Monitoring support
3x UART Ports
Betaflight support (Supports new DSHOT protocol)
BLHeli pass-through flashing supported by hardware
Black box (flash memory to 16MB)

STM32F405 (2MB flash) 32-bit processor
MPU6000 Gyro/Accelerometer
High quality 1.6mm PCB
Micro USB connector for programming
Dimensions: 27x27x6mm (includes USB in height)
Mounting Holes: 20mm square to center of holes
Weight: 4g

Lumenier BLHeli_32 30A 4S 4IN1 ESC

New 32bit Cortex-M0 running at 48MHz
Latest Gen. firmware using BLHeli_32
2-4s LiPo battery compatible
30A per channel, 40A burst
Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
Lightweight, and compact size
Adaptive timing, compatible with a wide range of motors and Kv
Synchronous rectification technology adds efficiency, damped light
Powerful regenerative braking / active braking.

Input: 2-4s LiPoly
Constant: 30 Amps (per channel)
Burst: 35Amps (per channel)
Dimensions: 33x36mm(including the power pads)
Mounting Holes: 20mm square to center of holes
Weight: 8g (without motor wires)

User Manual
Download the Micro LUX V3 Stack User Manual here.
The MICRO LUX V3 uses the LUXF4OSD target. Download Betaflight Configurator here.

1x Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack
Lumeneir LUX F4 + OSD Flight Controller (Designed for BetaFlight)
Lumenier 30A BLHeli_32 4in1 ESC (2-4s)
1x Set of plastic mounting hardware
4x M3x20 screws, 4x 5mm spacer, 4x 3mm spacer, 4x nuts
1x 330uF 25v Low ESR Capacitor
1x Set 16awg silicone power wire (90mm)


 2  Bewertungen

4 Sterne
3 Sterne
2 Sterne
1 Stern

Teilen Sie anderen Kunden Ihre Erfahrungen mit:

Einträge gesamt: 2
5 von 5
Top Teil für kleine Quads

ich betreibe diesen Stack in einem Armattan Gecko und bin sehr zufrieden mit diesem Combo. Der Stack lässt sich über Betaflight einfach updaten und einstellen.
Ebenso die BLHeli_32 ESC kann man einfach über das Tool konfigurieren.

Für kleine Quads kann ich ihn nur empfehlen...

5 von 5
Funktioniert perfekt!

Da der ESC von meinem BabyHawk R3 einen Ausfall hatte (ein Motor drehte sich nicht mehr), habe ich nach einem Ersatz gesucht. Schließlich wollte ich den Lumenier Micro LUX v3 ausprobieren, und das Ding funktioniert einfach perfekt.
Ich bin noch frisch in dem Hobby, aber ich habe im Vergleich zum F3 Board von babyhawk einen enormen Unterschied bemerkt. Das liegt mit Sicherheit an mehreren Aspekten - DSHOT1200, neue Betaflight firmware (BabyHawk R3 hat ohne Ende gesponnen mit Version 3.5.*). Und jetzt habe ich auf den Lumenier sogar Betafligth 4 gepackt. Morgen wirds getestet.