The Lumenier LUX MINI F7 Ultimate Flight Controller is the next generation of the popular Lumenier LUX flight controller lineup. It uses a powerful F7 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX MINI F7 Flight Controller. This MINI LUX F7 comes in a small 20x20 form factor weighin only 5g! Don't let the size of this flight controller fool you though, it is fully feature packed and works great on both micro and full sized drones.
The MINI LUX F7 builds on all the best features of its predecessors and further improves on hardware components and layout. You get a whopping 6x dedicated UART ports with built-in inversion for peripherals, along with built in 128Mbit 16MB flash memory for Blackbox recording. It includes an integrated BetaFlight OSD, making it super simple to show important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more.
Have you ever been in an FPV race where you need to plug in your quad, but you don't want to broadcast an FPV signal to knock your friends out of the air? Or how about you crash, and need to save your VTX from burning up while baking in the hot sun. With the LUX F7 you can remotely turn your VTX on or off via a switch on your radio! The LUX MINI F7 features an on-board LC VBAT filtered power pad designed to power your VTX. In addition it has an onboard 5v 3A regulator to power camera, Rx, and LEDs all at the same time. Using the PINIO resource, you can assign this pad to a switch on your radio, remotely controlling the power source to your video transmitter.
The Lumenier LUX MINI F7 supports all the popular accessories like beeer, camera control, smart audio / tramp VTX control, PWM outputs, and I2C connection.
UPDATE HISTORY
Version 1.2 update (March 2020)
Changed ICM20602 gyro to MPU6000 gyro for less sensitivity to noise and vibrations
NOTE: The newest version (board sold after March. 2020) of the LUX MINI FC with the MPU6000 Gyro have custom firmware for this board with BF 4.1.3 pre-loaded. Do no flash anything before 4.1.5 on this FC or it will not work. If you have an older version of the board, new firmware is backwards compatible.
Features
MCU: 216MHz STM32F722RET6
IMU: MPU6000
OSD: AB7456
Blackbox: 128Mbit / 16MByte
Anti-Vibration silicone grommets built in
6x Uarts with built-in inversion
1x Softserial supported
1x I2C
1x SH1.0_8pin connector (Vbat/G/Curr/TLM/S1/S2/S3/S4)
Vbat filtered output power for VTX
Camera control
Smartaudio & Tramp VTX protocol support (S/A UART 5 TX)
WS2812 Led Strip support
Beeper solder pad
Input: 6~36V (2~8S LiPo)
BEC: 5V 3A cont.
LDO 3.3V: Max.200mA
Software/Hardware Features
Betaflight support - target LUXMINIF7
BLHeli passthrough flashing supported by hardware
Specifications
High quality, gold plated PCB
Micro USB connector for programming
Dimensions: 28x28x6mm (includes USB in height)
Mounting Holes: 20mm square to center of holes
Weight: 5g
Includes
1x Lumenier LUX MINI F7 Ultimate Flight Controller
4x Anti-vibration silicone grommets (for M3 sized screws)
1x 8pin micro JST-SH 7cm connector for 4in1 ESC
1x set of mounting hardware
4x M3x25mm black oxide steel screws
4x M3x22mm black oxide steel screws
4x M3x5mm plastic spacer
4x M3x3mm plastic spacer
4x M3 rubber o-rings
8x M3 plastic hex nuts
Download the User Manual for Lumenier LUX MINI F7 Flight Controller
