Lumenier LUX HD AIO F7 FC 50A BL32 2-6S

Item number: 15373

EAN: 15858

89,95 €

including 19% VAT., plus shipping

Choose tax zone / country of delivery

Only 5 left in stock!
Available now! (Shipping time: 1 - 3 workdays)
Order within the next 2 days and 23 hours and 6 minutes and we will ship your order on 28.9.
Description

The Lumenier LUX HD AIO F7 Flight Controller + ESC is DJI HD system ready with an onboard 9v regulator to power the DJI Air Unit in a simple plug-and-play configuration. It uses a powerful F7 processor along with top-of-the-line hardware from the 50A BLHeli_32 2-6s powered by 4x F4 processors! Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX HD AIO F7 Flight Controller! This LUX HD AIO F7 comes in a standard 30.5x3.5 form factor weighing only 16.6g.

The LUX HD AIO F7 builds on all the best features of its predecessors and further improves on hardware components and layout, and is now dedicated to a design for the DJI digital HD system.

You get a whopping 6x dedicated UART ports with built-in inversion for peripherals. This Flight Controller features 1 onboard LC VBAT filtered power pad designed to power your DJI Air Unit at 9v and also other 5v accessories. The onboard 5v 3A regulator can be used to power the camera, Rx, and LEDs all at the same time, while the dedicated 9v 2A regulator reliably powers the DJI Air Unit or Vista system.

 

Features
Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us), and Multishot (5-25us). Auto-detection.
Synchronous rectification technology adds efficiency, damped light
New F4 MCUs (older ESCs use F0 at 48MHz)
Adaptive timing, compatible with a wide range of motors and Kv
Built-in 5v regulator that powers the LED system
Powerful regenerative braking / active braking.
BEC: 10v 2A cont. (for DJI HD System)
BEC: 5V 3A cont.
MCU: 216MHz STM32F722RET6
Anti-Vibration silicone grommets
Input: 8.4~36V (2~8S LiPo)
6 Uarts with built-in inversion
2-8s LiPo battery compatible
WS2812 Led Strip support
Beeper solder pad
LC Power Filter
IMU: MPU6000
Software/Hardware Features

Direct Plug and Play with DJI Air Unit or Caddx Vista
BLHeli passthrough flashing supported by hardware
Betaflight support - target LUXAIO
Firmware: BLHELI32(LUXAIO)


Specifications
Mounting Holes: 30.5mm square to the center of holes
Dimensions: 38x38x5mm (includes USB in height)
USB C connector for programming
High quality, gold plated PCB
Dimensions: 39x45x5mm
Constant: 50 Amps
Input: 2-8s LiPoly
Burst: 60 Amps
Weight: 16.6g
Downloads
Download the LUX HD AIO F7 User Manual
Download the stock Betaflight LUXAIO 4.2.9 HEX file for this AIO


Includes
1x Lumenier LUX HD AIO F7 FC + 50A BLHeli_32 2-8S ESC
1x 8pin (5 wire) micro JST-GH 8cm connector for DJI Air Unit
4x Anti-vibration silicone grommets (for M3 sized screws)
8x M3x8mm threaded hex plastic spacer
4x M3x35mm black oxide steel screws
4x M3x25mm black oxide steel screws
8x M3 silicone grommet insert (White)
4x M3 silicone grommet insert (Black)
1x 1000uF Low ESR Capacitor
1x set of mounting hardware
8x M3 plastic hex nuts
4x M3 rubber o-rings

Characteristics
Prozessor:
F7
Ratings

 0  Ratings

Write your first review and help others with their purchase decision: