Not only support 4S power, but also possesses high quality video and clear footage. What an awesome drone! Equipped with 1105 5000KV motors, new F4 V2 4S FC, BLHeli_32 and Caddx turtle V2 camera, using single N-channel MosFETs, soldering with 25V/220uf electrolytic capacitor, enable you to enjoy the powerful flight and beautiful scenery at the same time. Great choice for cruising, you can get tons of fun and speed in this cinewhoop.
F4 V2 FC board has added extra 4 pluggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting.
High performance STM32F405 processor FC boards and tuned Betaflight OMNIBUSF4SD (OBSD). Faster input signals with lower latency and higher update rate are reachable.
Using single N-channel MosFETs on ESC board which have a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
Soldering with 25V/220uf electrolytic capacitor, for protecting ESC board, reducing the defective rate caused by the instantaneous high voltage.
Installed with Caddx Tarsier 4K camera with ND8 fliter which supports APP setting and switchable resolution setting of 4K, 2.7k, 1440P, 1080P.
Upgraded 1105 motor from 6000KV to 5000KV, with a light weight but definitely will give you extreme power and speed. Motor comes with cable connectors.
Durable and light enough frame is customized for the Beta85X. To increase its stability, we specially add an extra stiffener brace of carbon fiber. Whole drone no soldering or tinkering necessary.
450mAh 4S high rate battery is recommended by default. But pilot could also use their own batteries with battery strap. Optional and affordable.
Weight: 80g (without battery)
F405 V2 Flight Controller and 16A BLHeli_32 ESC
Motors: 1105 5000KV with connector
Props: 2" 4-Blades Props
FPV HD-DVR-Kamera: CADDX Turtle V2
Receiver option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky / TBS Crossfire / PNP
Recommend battery: 4S 450mAh Battery (Not including)
5.8G FPV antenna
Flight time: 4min - 6min with 450mAh 4S battery
Find more details about this F405 V2 FC in another page.
CPU: STM32F405 (Overclock to 240MHz)
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Find more details about this BLHeli 32 ESC board in another page.
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
WHAT HAVE DONE TO SUPPORT 4S?
This Beta85X has upgraded in individual parts like FC, ESC, Motor, which can support 4S power with a steady performance and bring you into a glorious FPV world.
F4 FC & BLHeli_32 ESC
Support 4S Power. Written for ESC's that utilize 32-bit MCU. With the increase in processing power, faster input signals with lower latency and higher update rate would be possible in BLHeli_32, such as Dshot1200!
Using single N-channel MosFETs on ESC board, witch have a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
Current sensor included.
ESC is mounted on the frame by screws and connected with FC boards by cables.
Last Version: The performace of the ESC is limitted and could not stand 4S power on 85X for a long time. Besides, the ESC is connected to the FC board by header pins. When pluging the battery, the ESC will loose with the FC board and cause circut shot.
Soldering with 25V/220uf electrolytic capacitor, for reducing the defective rate caused by the instantaneous high voltage.
Last Version: Not power capacitor included, which have the risk that the permanently damage on ESC by impulse voltage when plug the battery.
1105 5000KV Motor
Lower 5000KV for new Beta85X 4S, which could support 4S power which won't cause the issue of overheat or burn (maybe the ESC). Also change motor cables from 30AWG to 28AWG.
Last Version: 1105 6000KV motors with 30AWG cables. In 4S power status, the motor will be overheat and damaged. Which may cause the burnt on the ESC.
Frame Stiffener Brace
The stiffener brace of carbon fiber can reinforce the Beta85X frame, avoid unstability caused by too strong power when Beta85x is flying.
Last Version: No stiffener brace included, which would result in seriously vibration on 4S power.
1 * Beta85X HD Whoop Quadcopter(4S)
1 * OSD Menu Board